Water Industrial Products

SS 304 3PIECE DESIGN BALL VALVE SCREWED ENDS CLASS-800

Three-piece ball valves are manufactured with one main body and two pipe connectors. The pipe connectors are typically threaded or welded to a pipe. This enables the main body to be easily removed for cleaning or repairs without having to remove the pipe connectors.

DROP FORGED STEEL GLOBE VALVE SCREWED ENDS CLASS-800

The exterior structure of a globe valve includes a valve body, handwheel, and bonnet. A threaded valve stem or screw connects to the handwheel and penetrates into the bonnet. On the interior end of the valve stem is a disc or plug, which can be a variety of shapes, depending on the application.

DROP FORGED STEEL GLOBE VALVE SOCKET WELDED ENDS CLASS-800

The exterior structure of a globe valve includes a valve body, handwheel, and bonnet. A threaded valve stem or screw connects to the handwheel and penetrates into the bonnet. On the interior end of the valve stem is a disc or plug, which can be a variety of shapes, depending on the application.

DROP FORGED STEEL HORIZONTAL LIFT CHECK VALVE SCREWED ENDS CLASS-800

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

DROP FORGED STEEL HORIZONTAL LIFT CHECK VALVE SOCKET WELD ENDS CLASS-800

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

DROP FORGED SS NEEDLE VALVE REGULATING TYPE SCREWED ENDS CLASS-800

A needle valve is used to accurately control flow rates of clean gasses or liquids. Gradual adjustments of the stem and plunger enable smooth flow control. These valves generally have low flow rates and a relatively significant pressure drop from the inlet to the outlet.

DROP FORGED STEEL GATE VALVE SCREWED END CLASS -800

A gate valve is the most common valve for water supply systems. It represents a linear-motion isolation valve and has a function to stop or allow the flow. Gate valves got their name from the closure element sliding into the flow stream to provide shutoff and, therefore, acting like a gate.

DROP FORGED SS THERMODYNAMIC STEAM TRAP SCREWED ENDS

The thermodynamic trap is an extremely robust steam trap with a simple mode of operation. The trap operates by means of the dynamic effect of flash steam as it passes through the trap, as depicted in the image below. The only moving part is the disc above the flat face inside the control chamber or cap.

CAST CARBON STEEL MOISTURE SEPARATOR FLANGE ENDS

Moisture separator is used to remove suspended water particles from steam line and supply dry steam to equipment, increasing their operational efficiency.

CAST CARBON STEEL SWING CHECK VALVE FLANGE END CLASS-600

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps

CAST CARBON STEEL SWING CHECK VALVE FLANGE END CLASS-300

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps

DROP FORGED STEEL GATE VALVE SOCKET WELD END CLASS -800

A gate valve is the most common valve for water supply systems. It represents a linear-motion isolation valve and has a function to stop or allow the flow. Gate valves got their name from the closure element sliding into the flow stream to provide shutoff and, therefore, acting like a gate.

CAST CARBON STEEL GLOBE VALVE FLANGE END CLASS-600

The exterior structure of a globe valve includes a valve body, handwheel, and bonnet. A threaded valve stem or screw connects to the handwheel and penetrates into the bonnet. On the interior end of the valve stem is a disc or plug, which can be a variety of shapes, depending on the application.

CAST CARBON STEEL STOP CUM NRV STRAIGHT PN-40

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

CAST CARBON STEEL GAUGE GLASS SET FLANGE END

The gauge consists of a vertical chamber that fills with the fluid from the tank or vessel. The level of fluid in the chamber matches the fluid level in the tank, and the level is dictated by the interface line between the liquid in the chamber and the vapor in the chamber.

CAST CARBON STEEL FEED CHECK VALVE FLANGE ENDS

Feed Check Valves are one of the most important components of boiler which control the flow of water from feed pump to the boiler and further prevents the backflow of water from boiler to pump when the boiler pressure is more than the pump pressure or when feed pump stops working.

CAST CARBON STEEL SINGLE POST HI-LIFT SAFETY VALVE FLANGED ENDS

A safety valve is a valve that acts as a fail-safe. An example of safety valve is a pressure relief valve (PRV), which automatically releases a substance from a boiler, pressure vessel, or other system, when the pressure or temperature exceeds preset limits.

CAST CARBON STEEL DOUBLE POST HI LIFT SAFETY VALVE FLANGE ENDS

A safety valve is a valve that acts as a fail-safe. An example of safety valve is a pressure relief valve (PRV), which automatically releases a substance from a boiler, pressure vessel, or other system, when the pressure or temperature exceeds preset limits.

CAST CARBON STEEL FULL LIFT SAFETY VALVE FLANGE ENDS

A safety valve is a valve that acts as a fail-safe. An example of safety valve is a pressure relief valve (PRV), which automatically releases a substance from a boiler, pressure vessel, or other system, when the pressure or temperature exceeds preset limits.

CAST CARBON STEEL FULL SAFETY VALVE FLANGE END CLASS 300

A safety valve is a valve that acts as a fail-safe. An example of safety valve is a pressure relief valve (PRV), which automatically releases a substance from a boiler, pressure vessel, or other system, when the pressure or temperature exceeds preset limits.

CAST CARBON STEEL PILOT OPERATED PRESSURE REDUCING VALVE FLANGED ENDS

A Pressure Reducing Valve (PRV) is an Automatic Control Valve designed to reduce a higher unregulated inlet pressure to a constant, reduced downstream (outlet) pressure regardless of variations in demand and/or upstream (inlet) water pressure.

CAST CARBON STEEL GATE VALVE FLANGE END CLASS-150

A gate valve is the most common valve for water supply systems. It represents a linear-motion isolation valve and has a function to stop or allow the flow. Gate valves got their name from the closure element sliding into the flow stream to provide shutoff and, therefore, acting like a gate.

CAST CARBON STEEL GATE VALVE FLANGE END CLASS-300

A gate valve is the most common valve for water supply systems. It represents a linear-motion isolation valve and has a function to stop or allow the flow. Gate valves got their name from the closure element sliding into the flow stream to provide shutoff and, therefore, acting like a gate.

CAST CARBON STEEL GATE VALVE FLANGE END CLASS-600

A gate valve is the most common valve for water supply systems. It represents a linear-motion isolation valve and has a function to stop or allow the flow. Gate valves got their name from the closure element sliding into the flow stream to provide shutoff and, therefore, acting like a gate.

CAST CARBON STEEL GLOBE VALVE FLANGE END CLASS-150

The exterior structure of a globe valve includes a valve body, handwheel, and bonnet. A threaded valve stem or screw connects to the handwheel and penetrates into the bonnet. On the interior end of the valve stem is a disc or plug, which can be a variety of shapes, depending on the application.

CAST CARBON STEEL GLOBE VALVE FLANGE END CLASS-300

The exterior structure of a globe valve includes a valve body, handwheel, and bonnet. A threaded valve stem or screw connects to the handwheel and penetrates into the bonnet. On the interior end of the valve stem is a disc or plug, which can be a variety of shapes, depending on the application.

CAST CARBON STEEL SWING CHECK VALVE FLANGE END CLASS-150

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

CAST CARBON STEEL PARALLEL SLIDE BLOW OFF VALVE FLANGE ENDS CLASS 300

A parallel slide gate valve is a type of valve used to control fluid flow in a piping system. The valve is made of two discs that are connected through a stem. It is mainly used for regulating fluid flow in oil and gas applications. These types of valves are easy to disassemble, clean, and repair

CAST CARBON STEEL GLOBE STEAM STOP VALVE RIGHT ANGLE PATTERN FLANGED ENDS PN-40

A main steam stop valve is a valve usually connected directly to the boiler for the purpose of shutting off the steam from the main steam line.

CAST CARBON STEEL Y TYPE STRAINER FLANGE END

The orientation of your Y strainer is going to depend on the media flowing through it. In steam or gas piping, it is best if your strainer is horizontal. This helps to stop water from collecting inside the pocket, which in turn helps prevent erosion.

CAST CARBON STEEL PISTON VALVE FLANGED ENDS PN-40

Piston valves are used for fully open or fully closed for on/off regulation on steam, gas, and other fluid services. These valves are mostly used on fluids that cause excessive seat wear. Piston valves are mostly actuated manually, but sometimes other actuation modes such as hydraulic and electric are used.

CAST CARBON STEEL PISTON VALVE FLANGED ENDS CLASS-150

Piston valves are used for fully open or fully closed for on/off regulation on steam, gas, and other fluid services. These valves are mostly used on fluids that cause excessive seat wear. Piston valves are mostly actuated manually, but sometimes other actuation modes such as hydraulic and electric are used.

CAST CARBON STEEL PISTON VALVE FLANGED ENDS CLASS-300

Piston valves are used for fully open or fully closed for on/off regulation on steam, gas, and other fluid services. These valves are mostly used on fluids that cause excessive seat wear. Piston valves are mostly actuated manually, but sometimes other actuation modes such as hydraulic and electric are used.

CAST CARBON STEEL GLOBE STEAM STOP VALVE FLANGED ENDS PN-40

Globe valves are easy to operate because they only require a quarter turn to open or close. A Handle or a lever attached to the stem opens or closes the valve This makes them ideal for applications where quick operation is necessary, such as in emergency situations.

CAST CARBON STEEL HORIZONTAL LIFT CHECK VALVE FLANGED ENDS PN-40

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

CAST CARBON STEEL PARALLEL SLIDE BLOW OFF VALVE FLANGE ENDS

A parallel slide gate valve is a type of valve used to control fluid flow in a piping system. The valve is made of two discs that are connected through a stem. It is mainly used for regulating fluid flow in oil and gas applications. These types of valves are easy to disassemble, clean, and repair

CAST IRON Y TYPE STRAINER FLANGED ENDS

The y strainer purpose is to remove unwanted particles from steam, gas, or liquid using a straining element typically made of wire mesh. Using this mechanical process in pipelines helps to protect everything from pumps to steam traps. Y strainers are sometimes designed with blow-off valves to make the cleaning process easier.

CAST IRON MOISTURE SEPARATOR

Moisture separator is used to remove suspended water particles from steam line and supply dry steam to equipment, increasing their operational efficiency.

CAST IRON BALL FLOAT STEAM TRAP SCREWED ENDS

Steam traps can be split into three main categories; Mechanical, Thermodynamic, and Thermostatic. Each type uses a different operating principle to remove condensate and non-condensable gases and keep steam in the system. The vast majority of steam traps in current operation are of the mechanical operated design.

C.I PILOT OPERATED PRESSURE REDUCING VALVE FLANGE ENDS

A Pressure Reducing Valve (PRV) is an Automatic Control Valve designed to reduce a higher unregulated inlet pressure to a constant, reduced downstream (outlet) pressure regardless of variations in demand and/or upstream (inlet) water pressure.

C.I STOP CUM NRV STRAIGHT FLANGED ENDS PN-16

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

C.I VERTICAL INVERTED BUCKET TYPE STEAM TRAP SCREWED ENDS

Steam traps are a type of automatic valve that filters out condensate (i.e. condensed steam) and non-condensable gases such as air without letting steam escape. In industry, steam is used regularly for heating or as a driving force for mechanical power.

C.I SINGLE POST HI LIFT SAFETY VALVE FLANGED ENDS

A safety valve is a valve that acts as a fail-safe. An example of safety valve is a pressure relief valve (PRV), which automatically releases a substance from a boiler, pressure vessel, or other system, when the pressure or temperature exceeds preset limits.

C.I ACCESSIBLE FEED CHECK VALVE FLANGE ENDS

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

C.I Y TYPE STRAINER SCREWED ENDS

This product is designed for remove foreign matter from pipe lines and provides protection for pumps, meters, valves, and other similar mechanical equipment, which is called as Strainer. "Y" Type Strainers are named after their shape and normally used for course filtration.

C.I DOUBLE POST HI LIFT SAFETY VALVE FLANGED ENDS

A safety valve is a valve that acts as a fail-safe. An example of safety valve is a pressure relief valve (PRV), which automatically releases a substance from a boiler, pressure vessel, or other system, when the pressure or temperature exceeds preset limits.

CAST IRON HORIZONTAL LIFT CHECK VALVE FLANGE END PN-10

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

CAST IRON HORIZONTAL LIFT CHECK VALVE FLANGE END PN-16

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

C.I HORIZONTAL LIFT CHECK VALVE RIGHT ANGLE PATTERN FLANGE END PN-16

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

C.I GLOBE STEAM STOP VALVE FLANGE ENDS PN-16

Globe Valves are made in accordance with various standard for low pressure throttling application up to 150 PSI working pressure. The handle is designed in wheel shape in order to rotate to open position or close position. It depends on disc element to regulate the flow of fluids in a pipeline.

C.I Y TYPE STRAINER FLANGE ENDS

The orientation of your Y strainer is going to depend on the media flowing through it. In steam or gas piping, it is best if your strainer is horizontal. This helps to stop water from collecting inside the pocket, which in turn helps prevent erosion.

CAST IRON REFLUX (N.R.V)VALVE FLANGE END PN-1.6

A reflux valve allows sewage to flow in one direction only and is intended to automatically close when flow reverses. Reflux valves are installed in the property sanitary drain, usually at properties that do not have an overflow relief gully (ORG) installed, however some properties may have both.

CAST IRON REFLUX (N.R.V) VALVE FLANGE END PN-1.0

A reflux valve allows sewage to flow in one direction only and is intended to automatically close when flow reverses. Reflux valves are installed in the property sanitary drain, usually at properties that do not have an overflow relief gully (ORG) installed, however some properties may have both.

CAST IRON GATE VALVE FLANGE ENDS PN-1.6

A gate valve is the most common valve for water supply systems. It represents a linear-motion isolation valve and has a function to stop or allow the flow. Gate valves got their name from the closure element sliding into the flow stream to provide shutoff and, therefore, acting like a gate.

CAST IRON Y TYPE STRAINER SCREWED ENDS

The orientation of your Y strainer is going to depend on the media flowing through it. In steam or gas piping, it is best if your strainer is horizontal. This helps to stop water from collecting inside the pocket, which in turn helps prevent erosion.

CAST IRON JUNCTION STEAM STOP VALVE FLANGE ENDS PN-16

Globe Valves are made in accordance with various standard for low pressure throttling application up to 150 PSI working pressure. The handle is designed in wheel shape in order to rotate to open position or close position. It depends on disc element to regulate the flow of fluids in a pipeline.

CAST IRON GLOBE STEAM STOP VALVE FLANGE ENDS PN-10

Globe Valves are made in accordance with various standard for low pressure throttling application up to 150 PSI working pressure. The handle is designed in wheel shape in order to rotate to open position or close position. It depends on disc element to regulate the flow of fluids in a pipeline.

C.I BALL VALVE 3PIECE DESIGN FLANGE ENDS

A Flange end ball valve is a full bore ball valve with a flanged connection. The usage of the flange end ball valve is to allow or stop the flow in the pipeline system and ensure the pressure within a pipeline system or process.

CAST IRON BALL VALVE SCREWED ENDS CLASS 125

A ball valve is a shut off valve that controls the flow of a liquid or gas by means of a rotary ball having a bore. By rotating the ball a quarter turn (90 degrees) around its axis, the medium can flow through or is blocked.

CAST IRON DUAL PLATE CHECK VALVE CLASS 125

The dual Plate Check Valve is an all-purpose non return valve that is much stronger, lighter in weight and smaller in size compared to a conventional swing check valve or life check valve. The Double Plate Check Valve working employs two spring-loaded plates hinged on a central hinge pin.

C.I KINETIC TYPE AIR RELEASE VALVE FLANGE ENDS

Air Release Valve function to release air pockets that collect at each high point of a full pressured pipeline. An air release valve can open against internal pressure, because the internal lever mechanism multiplies the float force to be greater than the internal pressure.

CAST IRON SLUICE VALVE FLANGE ENDS PN-1.6

These valves are used to regulate the flow of water in the pipe system by dividing into the number of sections. Check Valve: These valves are used to check the flow of water in reverse direction. These are generally provided on the delivery side of the pump. These valves work automatically

CAST IRON GATE VALVE FLANGE ENDS PN-1.0

A gate valve is the most common valve for water supply systems. It represents a linear-motion isolation valve and has a function to stop or allow the flow. Gate valves got their name from the closure element sliding into the flow stream to provide shutoff and, therefore, acting like a gate.

CAST IRON SLUICE VALVE FLANGE ENDS PN-1.0

These valves are used to regulate the flow of water in the pipe system by dividing into the number of sections. Check Valve: These valves are used to check the flow of water in reverse direction. These are generally provided on the delivery side of the pump. These valves work automatically

C.S BUTTERFLY VALVE WITH SS DISK CLASS -125

Butterfly valves are a family of quarter-turn rotational motion valves that are used in pipelines to shut-off flow. It is often said that butterfly valves can be used to regulate the flow. However, we do not recommend doing this, as it can damage the valve disk and have a negative effect on the sealing properties.

C.I BUTTERFLY VALVE WITH SS DISK PN-16

Butterfly valves are a family of quarter-turn rotational motion valves that are used in pipelines to shut-off flow. It is often said that butterfly valves can be used to regulate the flow. However, we do not recommend doing this, as it can damage the valve disk and have a negative effect on the sealing properties.

C.I BUTTERFLY VALVE WITH S.G IRON DISK PN-16

Butterfly valves are a family of quarter-turn rotational motion valves that are used in pipelines to shut-off flow. It is often said that butterfly valves can be used to regulate the flow. However, we do not recommend doing this, as it can damage the valve disk and have a negative effect on the sealing properties.

S.G IRON FLAP NRV PN-16

A non-return valve allows a medium to flow in only one direction and is fitted to ensure that the medium flows through a pipe in the right direction, where pressure conditions may otherwise cause reversed flow.

SS 304 ELBOW UNION

This is a fitting device which is bent in such a way to produce 90 degree change in the direction of flow of the content in the pipe. An Elbow is used to change the direction in piping

SS 304 HEX HEAD PLUG

SS 304 HEX CAP

STAINLESS STEEL HEX CAP AVAILABLE SIZES ARE 1/4"TO4"

SS 304 ELBOW 45DEGREE

This is a fitting device which is bent in such a way to produce 90 degree change in the direction of flow of the content in the pipe. An Elbow is used to change the direction in piping

C.I BUTTERFLY VALVE WITH SS DISK CLASS-125

Butterfly valves are a family of quarter-turn rotational motion valves that are used in pipelines to shut-off flow. It is often said that butterfly valves can be used to regulate the flow. However, we do not recommend doing this, as it can damage the valve disk and have a negative effect on the sealing properties.

C.I BUTTERFLY VALVE WITH S.G IRON DISK CLASS-125

Butterfly valves are a family of quarter-turn rotational motion valves that are used in pipelines to shut-off flow. It is often said that butterfly valves can be used to regulate the flow. However, we do not recommend doing this, as it can damage the valve disk and have a negative effect on the sealing properties.

SS 304 UNION COVER HORIZONTAL LIFT CHECK VALVE SCREWED ENDS

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

SS 304 ROUND CAP THREADED

AVAILABLE SIZES ARE 1/4" TO 4"

SS 304 HOSE NIPPLE

Hex nipple is a stainless steel 304 pipe fitting with male National Pipe Taper (NPT) threads on both ends for joining two pipes or extending pipe length.

SS 304 UNION

A union is a threaded fitting which allows the pipe work to be separated and reconnected without any horizontal movement in the pipe. It can be a standalone pipe fitting connecting two pieces of pipe, or an integral part of another fitting (such as a ball valve) which allows it to be separated.

SS 304 UNION BONNET GLOBE VALVE SCREWED ENDS PN 25

Globe valve is a linear motion valve and are primarily designed to stop, start and regulate flow. The disk of a Globe valve can be totally removed from the flowpath or it can completely close the flowpath. Conventional Globe valves may be used for isolation and throttling services.

SS 304 GLOBE VALVE SCREWED ENDS

A Globe valve is a linear motion valve and are primarily designed to stop, start and regulate flow. The disk of a Globe valve can be totally removed from the flowpath or it can completely close the flowpath. Conventional Globe valves may be used for isolation and throttling services.

SS 304 Y TYPE STRAINER SCREWED ENDS

A basket strainer uses a larger filtering part to hold more particles. While a Y-type strainer is installed either horizontally or vertically, a basket-type is installed only horizontally.

SS 304 GLOBE VALVE SCREWED ENDS PN 20

A Globe valve is a linear motion valve and are primarily designed to stop, start and regulate flow. The disk of a Globe valve can be totally removed from the flowpath or it can completely close the flowpath. Conventional Globe valves may be used for isolation and throttling services.

SS 304 M/F ELBOW

These are capable of withstanding high pressure and temperature, also resistant to corrosion and can be customized in terms of size and thickness as per requirement of the client.

SS 304 CROSS TEE

This is a fitting device which is bent in such a way to produce 90 degree change in the direction of flow of the content in the pipe. An Elbow is used to change the direction in piping and is also sometimes called a "quarter bend".

SS 304 SQUARE PLUG

The plug inserts into female pipes or fittings and connects with NPT threads, which create a tighter seal than straight threads. Features a square head for increased leverage and use with a wrench during installation and disassembly.

SS REDUCING HEX BUSH

Hex bushings are used to reduce the size of female threads from a larger to a smaller diameter. Hex Bushings are threaded fittings that have male threads on the outside and female threads on the inside with a hex head used to tighten the fitting into the threaded opening.

SS 304 REDUCING SOCKET

Sockets are used to join together two pieces of SS pipe of the same diameter.

SS 304 SOCKET THREADED END

SS 304 HEX NIPPLE

Hex nipple is a stainless steel 304 pipe fitting with male National Pipe Taper (NPT) threads on both ends for joining two pipes or extending pipe length.

SS 304 REDUCING HEX NIPPLE

Hex nipple is a stainless steel 304 pipe fitting with male National Pipe Taper (NPT) threads on both ends for joining two pipes or extending pipe length.

SS 304 COUPLING

Sockets are used to join together two pieces of SS pipe of the same diameter

SS 304 ELBOW

This is a fitting device which is bent in such a way to produce 90 degree change in the direction of flow of the content in the pipe. An Elbow is used to change the direction in piping and is also sometimes called a "quarter bend".

SS 304 TEE

These are capable of withstanding high pressure and temperature, also resistant to corrosion and can be customized in terms of size and thickness as per requirement of the client.

SS 304 HORIZONTAL LIFT CHECK VALVE SCREWED ENDS

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

SS 304 MULTI UTILITY CHECK VALVE SCREWED ENDS

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

SS 304 I.C GATE VALVE SCREWED END

A gate valve is the most common valve for water supply systems. It represents a linear-motion isolation valve and has a function to stop or allow the flow. Gate valves got their name from the closure element sliding into the flow stream to provide shutoff and, therefore, acting like a gate.

SS 304 VERTICAL LIFT CHECK VALVE SCREWED ENDS

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

SS 304 SEWING CHECK VALVE SCREWED ENDS

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.

SS 304 I.C NON SLAM CHECK VALVE CLASS-150

Check valves are one-way or nonreturn valves that open with fluid movement and pressure, and close to prevent backflow of the pressure to upstream equipment such as pumps and compressors. In fact, check valves allow the fluid to flow in only one direction.

SS 304 I.C BALL VALVE 3PIECE DESIGN FLANGE END CLASS 150

A flanged-type ball valve allows the operating fluid to flow when needed. It is very effective in providing positive leak-tight closure. For regulating or throttling purposes, a flanged-type ball valve is not suitable. The flanged ball valve is made of stainless steel.

SS 304 I.C NON SLAM CHECK VALVE CLASS-300

Check valves are one-way or nonreturn valves that open with fluid movement and pressure, and close to prevent backflow of the pressure to upstream equipment such as pumps and compressors. In fact, check valves allow the fluid to flow in only one direction.

INVESTMENT CASTING STAINLESS STEEL THERMODYNAMIC STEAM TRAP SCREWED ENDS

This type of steam trap operates by the internal energy and pressure of steam. Condensate that reaches to trap raise the disc and open the orifice and flow continuously by the help of the steam pressure which is behind the condensate through the discharge orifice.

SS 316 I.C BALL VALVE 3PIECE DESIGN FLANGE END CLASS 150

A flanged-type ball valve allows the operating fluid to flow when needed. It is very effective in providing positive leak-tight closure. For regulating or throttling purposes, a flanged-type ball valve is not suitable. The flanged ball valve is made of stainless steel.

SS 316 I.C BALL VALVE 2PIECE DESIGN SCREWED ENDS

A ball valve consists of a valve body in which a large sphere with a central hole equal to the inside diameter of the pipe is mounted. As the ball is rotated, in the fully open position the valve provides the through conduit or full bore required for unrestricted flow of the fluid and scrapers or pigs.

SS 304 I.C BALL VALVE 2PC DESIGN SCREWED ENDS

A ball valve consists of a valve body in which a large sphere with a central hole equal to the inside diameter of the pipe is mounted. As the ball is rotated, in the fully open position the valve provides the through conduit or full bore required for unrestricted flow of the fluid and scrapers or pigs.

SS 304 I.C BALL VALVE 2PIECE DESIGN SCREWED END PN-40

A ball valve consists of a valve body in which a large sphere with a central hole equal to the inside diameter of the pipe is mounted. As the ball is rotated, in the fully open position the valve provides the through conduit or full bore required for unrestricted flow of the fluid and scrapers or pigs.

SS 304 I.C BUTTERFLY HANDLE BALL VALVE 2PIECE DESIGN SCREWED ENDS PN-40

A ball valve consists of a valve body in which a large sphere with a central hole equal to the inside diameter of the pipe is mounted. As the ball is rotated, in the fully open position the valve provides the through conduit or full bore required for unrestricted flow of the fluid and scrapers or pigs.

Butterfly Valve Flange Type

AVAILABLE IN SIZES 1.5"-8"

Stainless Steel Union

STAINLESS STEEL Bib Cock Valve

Stainless Steel Manhole Cover

STAINLESS STEEL Reducing Elbow

Stainless steel Cross TEE

STAINLESS STEEL Camlock Coupling